Airlink101 airlink 101 awll6077 Manual do Utilizador

Wireless N USB Adapter Model # AWLL6077 User’s Manual Rev. 1.0

9 The ‘Wi-Fi Protected Setup – PBC method’ window will popup to acknowledge you the Adapter is starting to establish a connection. 2. Push the W

10 Step 3.2 Click the Available Network tab, select the SSID (Network Name) of the wireless network you wish to connect to, and click Add to Profil

11 The Adapter may automatically detect the Network Authentication and the Data encryption. You need to enter the security settings in the appropr

12 Troubleshooting If you are experiencing problems with the connection (unable to connect, low signal strength, slow connection speed, not work

13 4. Wireless Monitor This section describes the various functions of the Wireless Monitor that you can configure, including the settings of wirel

14 4.2 Profile Settings The Profile tab lists the current profiles and allows you to create new profiles. The Available Profile(s) box lists a

15 Enter a Profile Name and SSID. Enter the encryption settings for the profile. Click OK to save the changes. The Configuring Encryption secti

16 4.3 Available Network The Available network tab lists all of the networks that the adapter detects in your area. Clicking Refresh will refresh

17 4.4 Status The status section provides you with a list of information about the current status of the adapter.

18 4.5 Statistics The Statistics section gives you information about transmit and receive packet count.

1 Table of Contents 1. Introduction ...

19 4.6 Wi-Fi Protected Setup (WPS) The Wi-Fi Protected Setup™ (WPS) is a new and easy way to configure the encryption for your wireless network cli

20 Step 4.6.2a If you choose the Push Button method; click the Push Button Config (PBC) tab. Step 4.6.2b Push the WPS button on the router, and

21 Step 4.6.3a If you choose the Pin Code method, write down the PIN and click Yes. Select the Access Point that you want to connect, and then cl

22 Step 4.6.3b Log on to your router’s configuration page from the web browser and click on Wireless. Then click Wireless Security. Make sure tha

23 After a few moments both the router configuration screen and the adapter configuration screen should show a message telling you that a connecti

24 4.7 Configuring Encryption This section describes the different types of encryption available and how to configure them. In most cases, encrypti

25

26 4.7.1 Configuring WEP encryption Select WEP from the Data encryption box. Under Network Authentication, you will want to select Shared key

27 4.7.2 Configuring WPA/WPA2-PSK Encryption (for home users) Select WPA-PSK/WPA2-PSK from the Network Authentication box. Under Data encrypti

28 4.7.3 Configuring WPA/WPA2 Encryption (for corporate networks) Select WPA 802.1x / WPA2 802.1x from the Network Authentication box. Under Dat

2 1. Introduction Congratulations on your purchase of the Wireless N USB Adapter. Its high bandwidth combined with extended wireless coverage deliv

29 4.8 Ad-hoc and Peer-to-Peer Wireless Networks Ad-hoc networking is used when you want to connect two or more computers together but you don’t ha

30 You can also choose between no security or WEP security. If you choose WEP security, you can follow the instructions in the Configuring Encryptio

31 make sure that you do this on every ad-hoc machine so that they will all be set to the same channel. 4.9 About The About window provides the

32 Appendix A - Specification Frequency Band • 2.4Ghz Standards • IEEE 802.11b / 802.11g • IEEE 802.11n draft 2.0 Interface • USB 2.0 Data Ra

33 Technical Support E-mail: [email protected] Toll Free: 1-888-746-3238 Web Site: www.airlink101.com *Theore

3 2. Installation This section provides instructions on how to install the Wireless N USB Adapter. The driver is installed along with the utility.

4 Step 2.3 The Autorun screen will pop up. Select Install Utility and Driver from the menu. Note: If the Autorun screen doesn’t appear automat

5 Step 2.4 The Airlink101 WLAN Monitor screen will popup. Click Next at the screen. Step 2.5 Click Install to begin the installation.

6 Step 2.6 Give Permission to Window to install the driver software For Windows XP click Continue Anyway at the Windows Logo Screen. For Windows

7 3. Configuring the Adapter This section describes how to connect your wireless adapter to a wireless network. Open the Airlink101 Wireless Monit

8 Windows XP will show: The Airlink101 Wireless Monitor of Windows XP gives you an option to Start or Stop the Wireless Zero Configuration. It i